Controls are on the power hub, not the tool handle.

The Power Hub

The MakerX hub transfers the energy of a 20-volt lithium ion battery to any attached tool through a super flexible cord. The hub has an onboard power switch and variable speed control, negating the need for them to be incorporated into the individual tools. The kit we tested includes a rotary tool and an airbrush—but the hub can power additional MakerX tools, such as an angle grinder, heat gun, and burnisher. The WorX Power Share battery can provide up to three hours of power on a single charge, depending on the tool and how it’s being used.

Changing bits is easy with the integral spindle lock and the wrench supplied in the kit.

The rotary tool has excellent power, with speeds up to 35,000RPM.

The Rotary Tool

The handpiece has a comfortable ergonomic design with a soft-textured rubber grip. There’s plenty of power in the brushless motor, which allows for speeds from 5,000 to 35,000 RPM. We used several carving bits on pine and walnut blanks, and the tool performed well. The universal 1/8″ (3mm) collet holds any brand of rotary accessories.

The tool is not loud, but has a high-pitched whine, especially at faster speeds. It’s worth noting that the tool will shut off when pushed too hard. This is a design feature that surprised us at first—but it occurs so that the bit or blade will not kick back or become difficult to control. If this occurs, reset the system by turning the startup button on the hub off, and then turn on again. Once familiar with the tool, we were able to carve with minimal interruptions.

The compressor pump provides a stable base for the airbrush to stand upright.

The Airbrush

No noisy, bulky compressor or hose needed with the MakerX airbrush! The airbrush pen mounts directly onto a lightweight canister-type compressor that provdes 14-18 psi of air pressure. It also doubles as a comfortable handle for the brush, and solidly supports the unit upright when not in use. The pen itself is a high-quality tool that rivals those from well-known airbrush manufacturers.

Adjust paint flow with the knob on the end of the pen.

Conclusion

When you place all the elements of the system into the well-designed carry bag, you’ll truly appreciate the compact portability of the MakerX. The tote is lined with pockets to hold the tools safely and separately, with ample space left over for carving blanks, a water bottle, several bottles of paint, and an extra battery or two to keep you crafting on the go. The price is modest for the array of quality tools in the kit—not to mention the capability to power carve nearly anywhere you want.

Kit Contents

MakerX rotary tool

MakerX airbrush

Airbrush compressor

MakerX hub

20V battery

Battery charger

Accessory case

Storage bag

Steel brush (1)

Bristle brush (1)

Drum mandrel (1)

Cutting accessories (8)

Sanding accessories (12)

Polishing accessories (4)

Grinding accessories (5)

Engraving accessories (4)

Screw-on mandrel (1)

Threaded mandrel (1)

Drill bit: 1 1/8″ (29mm) (1)

Spanner wrench (1)

Dropper (1)

Cleaning brush (1)

Flexible Shaft vs. Micromotor

Flexible shaft tools are powerful. They can rip through wood at an astonishing rate. But most of them max out at 15,000 to 20,000 rpm, and the bits you generally use to add details, such as diamond and ruby, work better at higher speeds. That’s why most carvers switch to micromotors, which can reach speeds of 50,000 rpm, for intricate work.

And while flexible shaft tools are fine for larger projects clamped securely to a bench, I find them too powerful for smaller pieces that need to be handheld.

Using one, I find myself bracing against the bench and tightening my wrist muscles to withstand the power of the tool. I’m constantly adjusting my position to keep from bending the shaft too sharply, which makes the handpiece jerk around.

Micromotors, conversely, are less powerful but offer better speed and comfort. The handpiece connects to the power supply with a soft, flexible cord, and is easy to hold at all speeds. (I grip it in a fist when roughing out with carbide-point bits, and hold it like a pencil to carve fine detail.)

They are powered in one of two ways, by brushed or brushless motors. Because of how they are constructed, the brushless ones are noticeably more powerful (they tend to last longer, too). The rub is that they cost significantly more: brushed units start at $200, while brushless versions start at around $700. That’s where Foredom’s new brushless micromotor comes in—it lists for less than $600. And while you might expect that that price comes at the expense of other desirable attributes, the opposite is true: the K.1060 revs to 50,000 rpm and is one of the most user-friendly micromotors I’ve ever worked with.

Chuck in an aggressive carbide-point bit to remove waste wood in a hurry.

More Power = Faster Wood Removal

To test the Foredom, I first put an aggressive carbide-point bit in a brushed micromotor and dug into a piece of oak. I couldn’t press very hard before the bit bogged down and the motor stalled. With the K.1060, I had to apply a great deal more pressure to get the tool to stall, and it tore through the hard oak much faster. Not as fast as a flexible shaft tool, perhaps, but plenty fast for my purposes.

With a finer bit, like this fluted cylinder, you can carve fur flow and texture.

Digital Readout = Safer, Easier Use

Where most other micromotors have rough speed marks on the control dial, the Foredom has a precise digital readout, making it safer because you can make sure you’re not exceeding the bit manufacturer’s maximum allowed speed. Moreover, once you dial in a comfortable speed for different bits, you can easily return to that speed after changing them.

Handpiece

The K.1060’s quick-change handpiece accommodates bits with 3/32″ (2.4mm) and 1/8″ (3mm)-diameter shafts. Bit changes take seconds, and the collets grip well. As noted, the handpiece is comfortable to hold and the power cord is flexible and easy to maneuver.

Even finer bits, like this inverted cone (right), add more intricate detail. Below: a sample of bits the K.1060 can handle.

Workability

Power carver Lori Andrews creates most of her projects—including the bear on our cover—using flexible shaft tools. I duplicated her project using just the Foredom. While I had to substitute a smaller carbide-point bit—Lori uses a large cylinder-shaped one with a 1/4″ (6mm)-diameter shaft—I was able to carve the bear in a similar amount of time, quickly and easily. In fact, I prefer the high-speed tool for adding the fur details because it allowed me to take light, quick cuts.

Overall Opinion

If you already have and regularly use a flexible shaft tool, you may not need a micromotor this powerful. But if you’re looking to start power carving, especially if you’re having trouble using edged tools, I highly recommend this bad boy. For most of my power carving, it’s now the only tool I use.